Custom settings for Ender3

CrealityV1/Configuration.h

@@ -62,7 +62,7 @@
 // @section info
 
 // Author info of this build printed to the host during boot and M115
-#define STRING_CONFIG_H_AUTHOR "(thisiskeithb, Ender-3)" // Who made the changes.
+#define STRING_CONFIG_H_AUTHOR "(Benoit LORAND, Ender-3)" // Who made the changes.
 //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
 
 /**
@@ -80,10 +80,10 @@
 #define SHOW_BOOTSCREEN
 
 // Show the bitmap in Marlin/_Bootscreen.h on startup.
-#define SHOW_CUSTOM_BOOTSCREEN
+//#define SHOW_CUSTOM_BOOTSCREEN
 
 // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
-#define CUSTOM_STATUS_SCREEN_IMAGE
+//#define CUSTOM_STATUS_SCREEN_IMAGE
 
 // @section machine
 
@@ -136,7 +136,7 @@
 //#define BLUETOOTH
 
 // Name displayed in the LCD "Ready" message and Info menu
-#define CUSTOM_MACHINE_NAME "Ender-3"
+#define CUSTOM_MACHINE_NAME "BLD E3 BLTouch"
 
 // Printer's unique ID, used by some programs to differentiate between machines.
 // Choose your own or use a service like https://www.uuidgenerator.net/version4
@@ -1247,7 +1247,7 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-//#define BLTOUCH
+#define BLTOUCH
 
 /**
  * MagLev V4 probe by MDD
@@ -1378,7 +1378,7 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
+#define NOZZLE_TO_PROBE_OFFSET { -43, -5, 0 }
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
@@ -1608,7 +1608,7 @@
 #if ENABLED(MIN_SOFTWARE_ENDSTOPS)
   #define MIN_SOFTWARE_ENDSTOP_X
   #define MIN_SOFTWARE_ENDSTOP_Y
-  #define MIN_SOFTWARE_ENDSTOP_Z
+  //#define MIN_SOFTWARE_ENDSTOP_Z
   #define MIN_SOFTWARE_ENDSTOP_I
   #define MIN_SOFTWARE_ENDSTOP_J
   #define MIN_SOFTWARE_ENDSTOP_K
@@ -1744,7 +1744,7 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
+#define AUTO_BED_LEVELING_BILINEAR
 //#define AUTO_BED_LEVELING_UBL
 //#define MESH_BED_LEVELING
 
@@ -1945,7 +1945,7 @@
  * - Allows Z homing only when XY positions are known and trusted.
  * - If stepper drivers sleep, XY homing may be required again before Z homing.
  */
-//#define Z_SAFE_HOMING
+#define Z_SAFE_HOMING
 
 #if ENABLED(Z_SAFE_HOMING)
   #define Z_SAFE_HOMING_X_POINT X_CENTER  // X point for Z homing
@@ -2031,7 +2031,7 @@
  *   M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  */
 #define EEPROM_SETTINGS       // Persistent storage with M500 and M501
-//#define DISABLE_M503        // Saves ~2700 bytes of flash. Disable for release!
+#define DISABLE_M503        // Saves ~2700 bytes of flash. Disable for release!
 #define EEPROM_CHITCHAT       // Give feedback on EEPROM commands. Disable to save PROGMEM.
 #define EEPROM_BOOT_SILENT    // Keep M503 quiet and only give errors during first load
 #if ENABLED(EEPROM_SETTINGS)
@@ -2065,8 +2065,8 @@
 // Preheat Constants - Up to 6 are supported without changes
 //
 #define PREHEAT_1_LABEL       "PLA"
-#define PREHEAT_1_TEMP_HOTEND 185
+#define PREHEAT_1_TEMP_HOTEND 210
-#define PREHEAT_1_TEMP_BED     45
+#define PREHEAT_1_TEMP_BED     60
 #define PREHEAT_1_TEMP_CHAMBER 35
 #define PREHEAT_1_FAN_SPEED   255 // Value from 0 to 255
 
@@ -2382,7 +2382,7 @@
 // If you have a speaker that can produce tones, enable it here.
 // By default Marlin assumes you have a buzzer with a fixed frequency.
 //
-#define SPEAKER
+//#define SPEAKER
 
 //
 // The duration and frequency for the UI feedback sound.

CrealityV1/Configuration_adv.h

@@ -288,7 +288,7 @@
    * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
    * below 2.
    */
-  #define WATCH_TEMP_PERIOD  20               // Seconds
+  #define WATCH_TEMP_PERIOD  40               // Seconds
   #define WATCH_TEMP_INCREASE 2               // Degrees Celsius
 #endif
 
@@ -1282,7 +1282,7 @@
 //#define LCD_BACKLIGHT_TIMEOUT 30 // (s) Timeout before turning off the backlight
 
 #if HAS_BED_PROBE && EITHER(HAS_MARLINUI_MENU, HAS_TFT_LVGL_UI)
-  //#define PROBE_OFFSET_WIZARD       // Add a Probe Z Offset calibration option to the LCD menu
+  #define PROBE_OFFSET_WIZARD       // Add a Probe Z Offset calibration option to the LCD menu
   #if ENABLED(PROBE_OFFSET_WIZARD)
     /**
      * Enable to init the Probe Z-Offset when starting the Wizard.
@@ -1315,7 +1315,7 @@
   #endif
 
   // Include a page of printer information in the LCD Main Menu
-  #define LCD_INFO_MENU
+  //#define LCD_INFO_MENU
   #if ENABLED(LCD_INFO_MENU)
     //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
   #endif
@@ -2162,7 +2162,7 @@
 //
 // G2/G3 Arc Support
 //
-#define ARC_SUPPORT                   // Requires ~3226 bytes
+//#define ARC_SUPPORT                   // Requires ~3226 bytes
 #if ENABLED(ARC_SUPPORT)
   #define MIN_ARC_SEGMENT_MM      0.1 // (mm) Minimum length of each arc segment
   #define MAX_ARC_SEGMENT_MM      1.0 // (mm) Maximum length of each arc segment
@@ -3968,7 +3968,7 @@
  * Host Prompt Support enables Marlin to use the host for user prompts so
  * filament runout and other processes can be managed from the host side.
  */
-//#define HOST_ACTION_COMMANDS
+#define HOST_ACTION_COMMANDS
 #if ENABLED(HOST_ACTION_COMMANDS)
   //#define HOST_PAUSE_M76                // Tell the host to pause in response to M76
   //#define HOST_PROMPT_SUPPORT           // Initiate host prompts to get user feedback